PALADIN

PREAMP

Preamp was the first of the Paladin solid state products to be offered by Fearsome Sound.

Now available on  Reverb.com - Search for "Fearsome Sound".

High frequency Charge Pump power supply technology means the on-board solid state chip circuitry is provided with dual (positive and negative) voltages - an optimum environment for audio applications.

Preamp’s high impedance input is designed to accept and not colour your instrument or pedalboard signal chain output. If your signal is a little hot or cold, you can pad the signal up or down with Preamp’s input level control.

Three independent, level-controlled outputs are provided:

Headphone Out - mono output designed for 4 to 32 ohm stereo or mono headphones. Over the ear models perform best.

Unbalanced Out - low impedance output designed to drive an instrument amplifier input or the unbalanced input of an audio board or computer recording interface.

Balanced Out - low impedance, balanced, Tip, Ring Sleeve (TRS) output designed to drive a balanced  audio board input or computer recording interface.

The Tone Stack

The passive tone stack provides control of treble and bass boost and cut for all three outputs. The Tone Stack has essentially no effect on your signal when the controls are in the 12 o’clock position.

The Enclosure

Paladin Preamp is housed in a Hammond 1550C cast aluminum box. Dimensions are only slightly bigger than stompbox typical: Length 115mm (4.53in) x Width 90.0mm (3.54in) x Height 55.2 mm (2.17in).

Preamp Power Requirements

Preamp requires a  9vdc center negative voltage supply - typically a  power line from your regulated multi tap pedal board power supply. A quiet, regulated supply is critical. Preamp is not battery powered.

CHIRON Distortion

 Paladin Chiron Distortion is the latest solid state distortion pedal offered by Fearsome Sound.

Soon to be available on Reverb.com .

High frequency Charge Pump power supply technology means the on-board solid state chip circuitry is provided with dual (positive and negative) voltages - an optimum environment for audio applications.

Chiron's high impedance input is designed to accept, but not colour your instrument or pedalboard signal chain output.

Two independent, level controls are provided:

Drive - controls the distortion level impressed on your guitar signal.

Volume - low impedance output level control designed to drive the input of an instrument amplifier or the unbalanced input of an audio board or computer recording interface.

The Tone Stack

Chiron is not a Klon Centaur clone but its design is certainly inspired by the mid-boost feature of that classic design. The Chiron three-knob tone stack features a Paladin-typical passive treble and bass stack complemented by a an active midrange control for mid cut/scoop and boost. The Tone Stack has essentially no effect on your signal when the controls are in the 12 o’clock position.

The Enclosure

Paladin Chiron Distortion is housed in a Hammond 1590BB2 enclosure (470mm x 370mm x 150mm).  The Finish is black graphics on natural aluminum.

Chiron Distortion Power Requirements

Chiron requires a 9vdc center negative voltage supply - a power line from your regulated multi tap pedal board power supply is recommended. Chiron is not battery powered.

IMAGES COMING SOON

Distortion

Paladin Distortion iwas the first solid state distortion pedal  offered by Fearsome Sound.

High frequency Charge Pump power supply technology means the on-board solid state chip circuitry is provided with dual (positive and negative) voltages - an optimum environment for audio applications.

Distortion's high impedance input is designed to accept but not colour your instrument or pedalboard signal chain output.

Two independent, level controls are provided:

Drive - controls the distortion level impressed on your guitar signal.

Volume - low impedance output level control designed to drive the input of an instrument amplifier or the unbalanced input of an audio board or computer recording interface.

The Tone Stack

The passive tone stack provides control of treble and bass boost and cut. The Tone Stack has essentially no effect on your signal when the controls are in the 12 o’clock position.

The Enclosure

Paladin Distortion is housed in a Hammond 1550C cast aluminum box. Dimensions are stompbox typical: Length 115mm (4.53in) x Width 90.0mm (3.54in) x Height 55.2 mm (2.17in).

Distortion Power Requirements

Distortion  requires a  9vdc center negative voltage supply - a power line from your regulated multi tap pedal board power supply is recommended. Preamp is not battery powered.

Boost

Paladin Boost is a solid state clean signal boost pedal offered by Fearsome Sound.

High frequency Charge Pump power supply technology means the on-board solid state chip circuitry is provided with dual (positive and negative) voltages - the optimum environment for audio applications.

Boost's high impedance input is designed to accept your instrument or pedalboard signal chain output.

The LED "power on" indicator changes from Green to Red when you switch Boost into  bypass mode.

Controls provided:

Volume - low impedance output level control designed to drive the input of an instrument amplifier or the unbalanced input of an audio board or computer recording interface with a clean, boosted signal.

The Tone Stack

The passive tone stack provides control of treble and bass boost and cut. The Tone Stack has essentially no effect on your signal when the controls are in the 12 o’clock position.

The Enclosure

Paladin Boost is housed in a Hammond 1590BB2 enclosure (470mm x 370mm x150mm).  The Finish is black graphics on natural aluminum.

Boost Power Requirements

Boost  requires a  9vdc center negative voltage supply - a power line from your regulated multi tap pedal board power supply is recommended. Paladin Boost is not battery powered.